About XTOOL X100 PAD3 Key Programming Vehicle Coverage

 

XTOOL X100 PAD3 Auto Key Programmer Support All Key Lost Odometer Adjustment OBD2 Car Diagnostic Tool with KC100
XTOOL X100 PAD3 which is called X100 PAD Elite too, is a professional tablet key programmer which not only provides customers with key programming, but also supplies advanced special functions including Key programming, oil service light reset, timing belt service light reset, tire pressure warning light reset, EPB reset, throttle body reset, DPF reset, battery reset, steering angle calibration and OBD-II engine diagnosis, etc

37-2

Multi-Language: English, Spanish, French, Russian, German, Polish, Portuguese
Key Programmer XTOOL X100 PAD3 Functions:
* Key programming
* Oil Reset/Engine oil light reset
* Odometer Adjustment 
* Tire Pressure Warning Light Reset (Manual Operation)
* Timing belt light reset (Manual Operation)
* EPB Electrical Parking Brake Adaptation  
* TPS Throttle Body Adaptation 
* Steering Angle Calibration 
* Battery Reset 
* PIN Code Reading 
* Hexadcimal editor(Win Hex)
* OBDII Diagnosis
* INJ Code
* Support the latest vehicles with CAN BUS and UDS protocol
* Update Via WIFI (always equip your device with the latest software)
*More….

XTOOL X100 PAD3 Key Programming Features:
1.New keys programming
2. PIN Code reading with EEPROM
3.Hexadcimal editor(Win Hex)
4.Reads keys from immobilizer’s memory
5.New immobilizer programming
6.Vehicle Identification Number programming
7.Reset ECM & reset immobilizer
8.New remote controller programming
9.With full and strong database for the most important vehicle makes

XTOOL X100 PAD3 Key Programming Vehicle Coverage:
Asia: for Toyota, for Lexus, for Honda, for Acura, for Mazda, forNissan, for Infiniti, for Mitsubishi, for Subaru, for Suzuki, for Kia, for Hyundai, for Daewoo, for SSANGYONG, for Proton, etc

24-4
Europe: for Audi, for VW, for Skoda, for Seat, for Porsche, for Opel, for Citroen, for Peugeot, for Jaguar, for Land Rover, for Lincoln, for Renault, etc

24-5
America: forGM,for Cadillac, for Buick, for Chrysler, for Ford etc

24-6
China: for Great Wall, for Chery, for Brilliance-auto, for Geely, for LIFAN, for HAFEI, for CHANGAN, for LANDWIND, for BYD,for  BYD , for JAC, etc.

24-7

Specification :
Operating System: Android 5.1.1
Memory: 2GB RAM，64GB Flash
CPU: Quad Core, 1.8 GHz
Display 8.0 Inch IPS 5-Point Multi-touch Screen with 1024×600P Resolution
Sensors: Gravity Sensor, Light Sensor
Input/Output: Microphone, Dual Speakers, 3.5 mm headset jack, Mini HDMI Port, 2.0USBPort, TF Card Port
Battery: 10000mAh, 7.4V
Wi-Fi WIFI 2.4Ghz
Bluetooth 100 Meters
Power Voltage: 12V
Power Consumption: 29.6W
Operating Temperature: -20 to 50℃(-4 to 126℉)
Humidity: <90%

Dimension: (L*W*H): 240*177*30m

评论

发表评论

此博客中的热门博文

How to Read and Write Simos 18 ECU with KT200?

图片
  KT200 ecu programmer is the least expensive flasher to read Simos 18 ECU.   How to Read Simos 18 ECU with KT200? Below is the procedure to read the password (Step 1) and to set the control unit in the boot to read and write the file (step 2).   Step 1: Password search Kit to use: – Multifunction cable – Bench box – 2 resistances of 1000 Ω   Connect with the multifunction cable the following pinout and the connections on the pcb. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Password → PASSWORD SIMOS 18 BENCH BOX → Click on “Find Password” Kt200 Simos 18 Pinout 1 KT200 pinout Simos 18 RED: + 12V 6, 50, 86 BLACK: GROUND 1 BLUE: CAN-H 79 ORANGE: CAN-L 80 WHITE 71 BROWN 66 Kt200 Simos 18 Pinout 2 Now that the password has been found it’s possible to read and write the control unit. See next step.   Step 2: Read and Write ECU Connect with the multifunction cable the pinout. (Attention: Now remove the bench box) Do the connection shown below. Use the driver:...
阅读全文

How to check the status of Porsche piwis 3 tester System interface and Porsche PT3G VCI

图片
  How to check the status of Porsche piwis 3 tester System interface and Porsche PT3G VCI System interface The system interface is made up of the following areas: (1) Taskbar (2) Main page (3) Help function Task bar The task bar (1) displays the open programs and menus. Details are displayed as a tooltip. The following icons are available in the task bar: Main page On the main page (2), you can call up selected functions using the quick-access feature or switch to the main menus. Help function Call up the Help function (3) using the ? Help button. A search function is also available there. You can use this to look for certain contents in the Help. The full text search looks for terms in all texts that are available in the Help. Buttons in menus (F1 to F12) A bar containing quick-access function buttons is displayed at the bottom of some menus. The assignment varies depending on the menu. Tabs in menus There are several tabs in some menus. An active tab is gre...
阅读全文

Firmware Flash on CAT Comm Adapter 3 CAT Caterpillar ET Diagnostic Adapter III

图片
  Best Quality 2020C CAT Caterpillar ET Diagnostic Adapter III ： Update the firmware: 1)Connect CAT Comm Adapter 3 (CA3) to Diagnostic Port on the Engine (Key switch: ON). 2)Open CAT Communication Adapter 3 Toolkit 3)Select the middle Application Firmware Flash icon button which displays the options for firmware upgrades, or through Utilities – Reprogram CA3 menu. 4)Select a file to flash by clicking Select File, browse to (default: Program Files/ Program Files x86 – Caterpillar Inc – Comm Adapter 3 – Firmware) and select the file. 5)Click Open. 6) Click Begin to send the file. Files of the type “.bz2” for example, “CA3_1.23.54.tar.bz2”. 7)The file transfer takes approximately 2 minutes, at which point the following dialog box with the following message will display: “The file transfer was successful. Please wait while the CA3 is reprogrammed and then resets”. Click OK. 8)The CA3 Display Indicator Lights flashes in sequence while the new firmware is installe...
阅读全文