Benz S350 W221 ABR Control Module Programming by Launch X431

 

When ABR control module replacing,ABR can not work normally,upgrading ABR,you need to program it.So here i want to show you guide on how to use Launch X431 to program ABR module for Mercedes Benz S350 W211 Chassis.For more projects on Benz,please check here:Mercedes Benz Repair

What You Need?

Launch X431 Pro

Note:

1.Before executing this function, keep the vehicle battery not less than 12V and power adequate. When executing the programming , the device need connect the network.

2.During the execution of this function, do not abort by manual. Otherwise it will cause ABR Control unit cannot be used and other serve consequence.

3.Please do not ignore any prompt when coding.

Operation Procedure

1.Select Benz V48.11 above;

2.Select auto-search ;

3.Select ABR control unit;

4.Select control module programming function;

5.Note that the device prompts the control module for the execution of the program
4-1
6.After the confirmation condition is satisfied, the corresponding programming configuration file is downloaded from the network, and the network should be kept open
4-2
7.After the configuration file is downloaded, the control unit software version information and programming function execution conditions will be displayed
4-4
8.The programming operation is to code the control unit. If the action fails, the control unit module cannot be used properly. Click “yes” to start the programming operation
4-5
9.The programming interface shows the filename and programming progress that needs to be configured. The programming time may be longer.4-6

10.Hint after encoding has been successful, according to the equipment, some models will be prompted to close the ignition, after waiting for ten seconds to open the ignition switch, X431 device will reset to complete the control unit module,. The online coding has been completed.
4-7
More test report about Launch X431 please check:Launch X431 Test report

http://obd2scanner.info/2021/03/01/benz-s350-w221-abr-control-module-programming-by-launch-x431/

评论

发表评论

此博客中的热门博文

How to Read and Write Simos 18 ECU with KT200?

图片
  KT200 ecu programmer is the least expensive flasher to read Simos 18 ECU.   How to Read Simos 18 ECU with KT200? Below is the procedure to read the password (Step 1) and to set the control unit in the boot to read and write the file (step 2).   Step 1: Password search Kit to use: – Multifunction cable – Bench box – 2 resistances of 1000 Ω   Connect with the multifunction cable the following pinout and the connections on the pcb. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Password → PASSWORD SIMOS 18 BENCH BOX → Click on “Find Password” Kt200 Simos 18 Pinout 1 KT200 pinout Simos 18 RED: + 12V 6, 50, 86 BLACK: GROUND 1 BLUE: CAN-H 79 ORANGE: CAN-L 80 WHITE 71 BROWN 66 Kt200 Simos 18 Pinout 2 Now that the password has been found it’s possible to read and write the control unit. See next step.   Step 2: Read and Write ECU Connect with the multifunction cable the pinout. (Attention: Now remove the bench box) Do the connection shown below. Use the driver: → TOOLS BOOT MODE → INF
阅读全文

The Nexiq USB Link 2 Diagnostic Tools for Trucks

图片
  The Nexiq USB Link 2 is a hardware device that enables service bay personal computer to retrieve vehicle information using either wireless Bluetooth technology or more traditional cable connection. Once configured, the USB Link 2 interfaces with your PC, enabling you to use specific PC applications to perform vehicle diagnostics. Dependable and rugged, the new USB-Link 2 is five times faster than its predecessor. It has sixteen times more random access memory than the old USB-Link, and it supports heavier bus loads on simultaneous channels. The Nexiq USB Link 2 also includes a new Bluetooth* module with an enhanced data rate to support wireless communication (500 b/s J1939). For even more reliability, we’ve upgraded the USB connector to a more robust, automotive grade connector with a latching mechanism. The USB-Link 2 is compatible with a wide range of OEM software applications. The Nexiq USB Link 2 comes with the following: Latching USB Cable (Part # 404032) 9 pin
阅读全文

MSULTRA MAXISYS ULTRA TABLET

图片
  The MaxiSYS Ultra is Autel’s most ambitious diagnostics tablet designed to maximize technician intelligence. Autel Maxisys Ultra features a 13-inch touchscreen tablet with Android 7.0 OS powered by an Octa-core processor (2.3GHz Quad + 1.7GHz Quad), substantial 256GB built-in memory, all powering the new split-screen multi-application navigation to provide diagnostic guidance and test components to confirm repairs. Combined with the dynamic topology module mapping, enhanced Auto SCAN features and Intelligent Diagnostics options, the Ultra offers the technicians step-by-step repair guidance. The new MaxiFlash VCMI functions as a 4-channel oscilloscope, waveform generator, multimeter, and CAN BUS tester. The convenient docking station featured ensures you always have the power to scan. MaxiSYS Ultra Features · Large 12.9’’ Touchscreen (2732 x 2048) · Android 7.0 · 2.3GHz + 1.7GHz Octa-core Processor / 256GB Memory · Advanced VCMI 5-In-1 Device: VCI, Oscilloscope,
阅读全文