Newest Nissan Consult 3 Plus

 

What Nissan Consult 3 Plus?
Nissan Consult 3 Plus
Nissan Diagnostic Tools Nissan Consult 3 is a diagnostic software special for Nissan,support all the models of the Nissan and Infiniti from 1996 up till now, with all Consult II & III functions.It can support all Nissan car,Infiniti carand Nissan GTR.

Nissan Consult 3 Plus Functions List:

Supports ECM reprogramming on most 1999 model year and later and some TCM and ABS/VDC reprogramming.

Supports blank ECM and TCM programming.

Supports ECM reprogramming on most 1999 model year and later and some TCM and ABS/VDC reprogramming.

Supports blank ECM and TCM programming. September 2013 Nissan and Infiniti began the phase-in of “blank” service part ECMs and TCMs. Depending on the model and model year, replacement modules come WITHOUT software. When the replacement module is installed in an applicable vehicle for any reason, it will need to be programmed.

 Top 5 Reasons to Get Nissan Consult 3 Plus:

1.Consult-3 plus = Consult-3 for Nissan + Consult-2 for Nissan
2.Software Version: CSP Software Version : CSP V41.10; Programming Data Version : plus_V75
3.Supports all the models of the Nissan and Infiniti from 1996 to 2018, with all Consult II & III functions .
4.Calcaulate the password for the new cars till year 2018 with NISSAN Password.
5.Supports ECU Programming without card
6.Can be installed on Windows XP, WIN7
7.Suppored Languages: English, Chinese, Finnish, French, German, Greek, Italian, Japanese, Portuguese,Russian, Spanish, Turkish, Thai, Czech, Polish, Hungarian
4-1
PC Based: PC Require

Model Year Coverage: The Consult-III Plus is required for all 2013 and newer Nissan and Infiniti vehicles. In addition, the Consult-III Plus is required for all: 2011 and newer Nissan LEAF, Quest, and Murano CrossCabriolet vehicles; 2012 and newer Nissan GT-R and NV vehicles; and 2012 and newer Infiniti M and M Hybrid vehicles. The Nissan Consult 3 Plus is continuously being updated to accommodate new vehicles as well as older model years dating back as far as 1996.

Nissan Consult 3 Plus Support Car Models:

Diagnostics:for all Nissan,Infiniti,GTR
Immo and Smart key:for all Nissan,Infiniti,GTR
Nissan GTR: for Nissan GTR Diagbostics and Immobi
Electromobiles car:for Nissan Electromobiles car Diagbostics and Immo
Nissan and Infiniti from 1996 up till now
Note:Consult III Plus – 1996MY up

Nissan Consult 3 Plus Installation Guide:
The installation methods of different Consult 3 may be similar,if there here is no version that you have or you have higher version,please try to install it referring to these method by yourself.

FAQ
Q1: What is the difference among Nissan consult 3, consult 4 and Nissan consult 3 plus? Can Nissan consult 4 remap ECU and change IGN time-limited parameter?
A1:
1) Nissan consult 3 and consult 4 share the same software version and parts, the difference between them is the appearance and the quality;
2) Nissan consult3 plus is the newest-released Nissan diagnostic  it supports the Nissan up to 2018 year. And only Nissan Consult 3 Plus can support programming.

Q2: What additional card needed when use Nissan Consult-3 plus to make key?
A2: It need additional card, it needs for making key, this card is Nissan Consult-3 plus Security Card, otherwise the button “Immobilizer key” is gray color and is unavailable

Q3: Can i use this nissan consult 3 plus to program tcm and bcm?
A2: Yes, but you need to have the program file.

Q4: Does your Nissan consult 3 plus contain Battery registration card?
A6: No, it doesn’t.

Q5: Do you have any instruction for software installation?
A7: Yes. There is the software installation video on our website. There is the software installation manual in the package too. You can follow them to install the software. Attention: Nissan consult software must be installed on XP system.

Q6: Can i use your nissan consult 3 to program tcm and bcm?
A8: This nissan consult 3 plus support this two function. But if you want to use this two function, you need have the programming file by yourself.

5-1

 

For more information please visit our website sale@cnautotool.com

 

http://obd2scantool.net/2021/03/05/newest-nissan-consult-3-plus/

评论

发表评论

此博客中的热门博文

How to Read and Write Simos 18 ECU with KT200?

图片
  KT200 ecu programmer is the least expensive flasher to read Simos 18 ECU.   How to Read Simos 18 ECU with KT200? Below is the procedure to read the password (Step 1) and to set the control unit in the boot to read and write the file (step 2).   Step 1: Password search Kit to use: – Multifunction cable – Bench box – 2 resistances of 1000 Ω   Connect with the multifunction cable the following pinout and the connections on the pcb. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Password → PASSWORD SIMOS 18 BENCH BOX → Click on “Find Password” Kt200 Simos 18 Pinout 1 KT200 pinout Simos 18 RED: + 12V 6, 50, 86 BLACK: GROUND 1 BLUE: CAN-H 79 ORANGE: CAN-L 80 WHITE 71 BROWN 66 Kt200 Simos 18 Pinout 2 Now that the password has been found it’s possible to read and write the control unit. See next step.   Step 2: Read and Write ECU Connect with the multifunction cable the pinout. (Attention: Now remove the bench box) Do the connection shown below. Use the driver:...
阅读全文

How to check the status of Porsche piwis 3 tester System interface and Porsche PT3G VCI

图片
  How to check the status of Porsche piwis 3 tester System interface and Porsche PT3G VCI System interface The system interface is made up of the following areas: (1) Taskbar (2) Main page (3) Help function Task bar The task bar (1) displays the open programs and menus. Details are displayed as a tooltip. The following icons are available in the task bar: Main page On the main page (2), you can call up selected functions using the quick-access feature or switch to the main menus. Help function Call up the Help function (3) using the ? Help button. A search function is also available there. You can use this to look for certain contents in the Help. The full text search looks for terms in all texts that are available in the Help. Buttons in menus (F1 to F12) A bar containing quick-access function buttons is displayed at the bottom of some menus. The assignment varies depending on the menu. Tabs in menus There are several tabs in some menus. An active tab is gre...
阅读全文

Firmware Flash on CAT Comm Adapter 3 CAT Caterpillar ET Diagnostic Adapter III

图片
  Best Quality 2020C CAT Caterpillar ET Diagnostic Adapter III ： Update the firmware: 1)Connect CAT Comm Adapter 3 (CA3) to Diagnostic Port on the Engine (Key switch: ON). 2)Open CAT Communication Adapter 3 Toolkit 3)Select the middle Application Firmware Flash icon button which displays the options for firmware upgrades, or through Utilities – Reprogram CA3 menu. 4)Select a file to flash by clicking Select File, browse to (default: Program Files/ Program Files x86 – Caterpillar Inc – Comm Adapter 3 – Firmware) and select the file. 5)Click Open. 6) Click Begin to send the file. Files of the type “.bz2” for example, “CA3_1.23.54.tar.bz2”. 7)The file transfer takes approximately 2 minutes, at which point the following dialog box with the following message will display: “The file transfer was successful. Please wait while the CA3 is reprogrammed and then resets”. Click OK. 8)The CA3 Display Indicator Lights flashes in sequence while the new firmware is installe...
阅读全文