2021 Suzuki Swift odometer calibration by Xtool X100 Pad2

 

Xtool X100 Pad2 is supported to successfully perform odometer calibration for a Suzuki Swift 2021 RH850 VDO via OBD. It’s a very easy and quick job in 1 minute.

Follow the steps below to learn how to do it.

The mileage on dashboard is 2910km now.

Connect X100 Pad2 with OBD, press

Instrument cluster >> Suzuki >> Swift >> 2020- >> RH850 VDO >> Mileage adjustment





 

Please input the file name to save it:

The file is saved the original vehicle data, not to be overwritten.



The EEPROM data is successfully backed up.
Press “OK”.

Enter the new mileage:2995km.

Repaired successfully.

Amazing speed!

The dashboard changed almost at once to 2995 km.

Done!

评论

发表评论

此博客中的热门博文

How to Read and Write Simos 18 ECU with KT200?

图片
  KT200 ecu programmer is the least expensive flasher to read Simos 18 ECU.   How to Read Simos 18 ECU with KT200? Below is the procedure to read the password (Step 1) and to set the control unit in the boot to read and write the file (step 2).   Step 1: Password search Kit to use: – Multifunction cable – Bench box – 2 resistances of 1000 Ω   Connect with the multifunction cable the following pinout and the connections on the pcb. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Password → PASSWORD SIMOS 18 BENCH BOX → Click on “Find Password” Kt200 Simos 18 Pinout 1 KT200 pinout Simos 18 RED: + 12V 6, 50, 86 BLACK: GROUND 1 BLUE: CAN-H 79 ORANGE: CAN-L 80 WHITE 71 BROWN 66 Kt200 Simos 18 Pinout 2 Now that the password has been found it’s possible to read and write the control unit. See next step.   Step 2: Read and Write ECU Connect with the multifunction cable the pinout. (Attention: Now remove the bench box) Do the connection shown below. Use the driver:...
阅读全文

How to check the status of Porsche piwis 3 tester System interface and Porsche PT3G VCI

图片
  How to check the status of Porsche piwis 3 tester System interface and Porsche PT3G VCI System interface The system interface is made up of the following areas: (1) Taskbar (2) Main page (3) Help function Task bar The task bar (1) displays the open programs and menus. Details are displayed as a tooltip. The following icons are available in the task bar: Main page On the main page (2), you can call up selected functions using the quick-access feature or switch to the main menus. Help function Call up the Help function (3) using the ? Help button. A search function is also available there. You can use this to look for certain contents in the Help. The full text search looks for terms in all texts that are available in the Help. Buttons in menus (F1 to F12) A bar containing quick-access function buttons is displayed at the bottom of some menus. The assignment varies depending on the menu. Tabs in menus There are several tabs in some menus. An active tab is gre...
阅读全文

Firmware Flash on CAT Comm Adapter 3 CAT Caterpillar ET Diagnostic Adapter III

图片
  Best Quality 2020C CAT Caterpillar ET Diagnostic Adapter III ： Update the firmware: 1)Connect CAT Comm Adapter 3 (CA3) to Diagnostic Port on the Engine (Key switch: ON). 2)Open CAT Communication Adapter 3 Toolkit 3)Select the middle Application Firmware Flash icon button which displays the options for firmware upgrades, or through Utilities – Reprogram CA3 menu. 4)Select a file to flash by clicking Select File, browse to (default: Program Files/ Program Files x86 – Caterpillar Inc – Comm Adapter 3 – Firmware) and select the file. 5)Click Open. 6) Click Begin to send the file. Files of the type “.bz2” for example, “CA3_1.23.54.tar.bz2”. 7)The file transfer takes approximately 2 minutes, at which point the following dialog box with the following message will display: “The file transfer was successful. Please wait while the CA3 is reprogrammed and then resets”. Click OK. 8)The CA3 Display Indicator Lights flashes in sequence while the new firmware is installe...
阅读全文